FORGING MANIPULATOR 5TON
FORGING MANIPULATOR 5TON
Introduction
Forge manipulator 5ton, electrical
Manufactured in 1990
Revamped in January 2005
Topics of revamping: through modification of hydraulic system
Main Pump = REXROTH A10VSO (good condition)
Main distributor = SAUER DANFOSS PVG 120 (good condition)
Other components = BOSCH – REXORTH (good condition)
Traction Motor: Radial piston SAI (good condition)
Spindle Motor: radial piston SAI (good condition)
Joysticks = two, digital (CAN BUS), commanding jaw movements via PLC
PLC = Moeller
Display = Moeller, showing diagnostic data, pressure
Main features:
Jaw pressure control system: pressure can be preset and is controlled
Electroning servo-commands
High efficiency hydraulics, good general condition
Rear traction by radial piston motor + differential
Technical data
CAPACITY
Nominal lifting capacity: 5ton
Max lifting capacity (off duty): 5.5ton
Charging moment: 14ton*m
TRAVEL
Travelling speed: 0-60m/min
Traction: Rear side
Turning radius: 3.8m
ROTATION
Continuous rotation speed range: 0 ÷ 25 (adjustable)rpm
PARALLEL LIFTING
Minimum height: 700mm
Maximum height: 1500mm
Parallel stroke: 800mm
Lifting speed: 0 ÷ 200mm/s
TILTING
Upward: 12°
Downward: Floor level
TONGS
Opening time: 10sec
Clamping diameter -mm
Square -mm
TONG EXTENSIONS
Max clamping dia: 2200mm
INSTALLED POWER
Main motor: 37kW
Auxiliaries: 4kW
WEIGHT
Total mass: 27’000kg
MAIN DIMENSIONS
Length (with extensions): 6.3m
Width: 2.3m
Height (excluded cable hook): 3.4m
Actual condition
Ref. 51331
SMERAL LHK 1200 TONS UPSETTER / SMERAL GKN-800 TONS UPSETTER
SMERAL LHK 1200 TONS UPSETTER / SMERAL GKN-800 TONS UPSETTER
UPSETTER
UPSETTER LHK 1200 Ton
Made: CSR/TOS Czech Republic, Press capacity: 1 200 ToF, Tightening capacity: 420 ToF, Total stroke: 500 mm, Stroke of main crank shaft: 318 mm, Stroke of mobile die: 215 mm, Stroke/min: 27, Bar diameter: 50-90 (150) mm, Max diameter of piece: 152mm, Max weight of piece: 5 kg, Main motor power: 75 KW, Area of machine : 6400 x 4420 mm, Height of machine: 3830 mm, Weight: 128.7 Ton On this machine, it used to be made bearing rings, maximum outer diameter Ø 152, for oscillating bearings with balls, radial bearings and tapered rollers bearings.
UPSETTER GKN-800 Ton SMERAL
Made in: CSR/TOS Czech Republic, Press capacity: 800 ToF, Tightening capacity: 280 ToF, Total stroke: 500 mm, Stroke of main crank shaft: 380 mm, Stroke of mobile die: 159 mm, Stroke/min: 35, Bar diam.: 36-70 mm, Max diam. of piece: 100 mm, Max weight of piece: 3.3 kg, Main motor power: 40 KW, Machine area: 5350 x 3600 mm, Height of machine: 3060 mm, Weight: 82 To. On this machine, it used to be made bearing rings, maximum outer diameter Ø 100, for oscillating bearings with balls, radial bearings and tapered rollers bearings.
Ref. 51332
FORGING PRESS & MANIPULATOR
Open Die Forging Press
a) HBE Stock No.U04 1000 Ton Four Column Push Down Open Die Forging Press (LOWEY) 1 set Used, Rebuilt HBE Plant
b) HBE Stock No.U05 800 Ton Four Column Push Down Open Die Forging Press (LOWEY) 1 set Used, Rebuilt HBE Plant
Rail Bound Manipulator
c) HBE Stock No.U01 20Ton/40MT Rail Bound Manipulator (DDS) 1 set Used, Rebuilt HBE Plant
Ref. 51342
BIRDSBORO 2600 TONS HYDRAULIC HOT OPEN DIE
2600 TON BIRDSBORO HYDRAULIC HOT OPEN DIE
4-POST FORGING PRESS, NEW in 1950’S
SPECIFICATIONS:
Capacity @ 5000 psi 2600 Ton
Bed Area F-B, L-R 30” x 44”
Daylight 72”
Stroke 30”
Ram Size-Diameter 36”
Return Rams-Diameter 14”
Column Size (4) 15.75” dia.
Main Motor 300 HP
Capacity Pump-Water/Hydraulic 120 GPM
Footprint-Press Only 9’ x 12’
Height 16’5”
Ref. 51343
